Building materials
BS EN 13238 Pretreatment of building materials samples

BS EN 13238:2010
Reaction to fire tests for building products. Conditioning procedures and general rules for selection of substrates
Building material sample pretreatment
https://shop.bsigroup.com/ProductDetail/?pid=000000000030166839

Pretreatment environment:
23+ -2 degrees, 50+ -5%
Requirements: At least 48 hours, until the weight; once every 24 hours, the quality does not exceed 0.1% or 0.1g. That's a big deal.

Fixed sample, laboratory 'assembly, construction' samples.
To remove excess water, the moisture content should be less than 40%.
Pretreated for 8 weeks, flame retardant wood and flame retardant treated wood products. Cement products.
Pretreatment for 4 weeks, common wood products, calcium silicate, gypsum products, and other absorbent materials.
Pretreatment for 2 weeks, other products.

Base plate:
Floor class,
The final used substrate density is at least 75% of the test substrate. That is, the density density of the bottom plate used for testing cannot be too high.
The final bottom plate is non-wood, the whole is A1 or A2, then the cement fiber board is 8mm thick, the density is about 1800, and there is no bottom plate when testing.
The final bottom plate is wood. The whole is A1 or A2. The ordinary particleboard is 20mm thick and the density is 680. The test is C grade.
The final bottom plate is not wood, and the whole is not A1 or A2, and the bottom plate is used according to the actual use.

Tablet class, SBI
The base plate type is based on the principle of actual use
Calcium silicate board can not replace gypsum board
If the sample surface is actually using an 'air gap', the groove, the sample should be at least 25 mm deep.
Backplane type:
5da885aac5d95

BS EN 13238:2010 Reaction to fire tests for building products. Conditioning procedures and general rules for selection of substrates Building material sample pretreatment https://shop.bsigroup.com/ProductDetail/?pid=000000000030166839 Pretreatment environment: 23+ -2 degrees, 50+ -5% Requirements: At least 48 hours, until the weight; once every 24 hours, the quality does not exceed 0.1% or 0.1g. That's a big deal. Fixed sample, laboratory 'assembly, construction' samples. To remove excess water, the moisture content should be less than 40%. Pretreated for 8 weeks, flame retardant wood and flame retardant treated wood products. Cement products. Pretreatment for 4 weeks, common wood products, calcium silicate, gypsum products, and other absorbent materials. Pretreatment for 2 weeks, other products. Base plate: Floor class, The final used substrate density is at least 75% of the test substrate. That is, the density density of the bottom plate used for testing cannot be too high. The final bottom plate is non-wood, the whole is A1 or A2, then the cement fiber board is 8mm thick, the density is about 1800, and there is no bottom plate when testing. The final bottom plate is wood. The whole is A1 or A2. The ordinary particleboard is 20mm thick and the density is 680. The test is C grade. The final bottom plate is not wood, and the whole is not A1 or A2, and the bottom plate is used according to the actual use. Tablet class, SBI The base plate type is based on the principle of actual use Calcium silicate board can not replace gypsum board If the sample surface is actually using an 'air gap', the groove, the sample should be at least 25 mm deep. Backplane type: ![5da885aac5d95](serve/attachment&path=5da885aac5d95)
116
0
1
live preview
enter atleast 10 characters
WARNING: You mentioned %MENTIONS%, but they cannot see this message and will not be notified
Saving...
Saved
With selected deselect posts show selected posts
All posts under this topic will be deleted ?
Pending draft ... Click to resume editing
Discard draft